To change the WiFi on a Ring Video Doorbell, open the Ring app, go to Devices, select your doorbell, tap Device Health, then tap Change WiFi Network (or Reconnect to WiFi). The app uses Bluetooth to put the doorbell in setup mode, then guides you through selecting your new network and entering the password. The whole process takes about five minutes.
Key takeaways:
-
The process is the same across all Ring Video Doorbell models, app → Device Health → Change WiFi Network
-
You must be physically near the doorbell during setup (Bluetooth range, roughly 30 feet)
-
Ring doorbells only connect to 2.4 GHz WiFi, not 5 GHz (with limited exceptions noted below)
-
You do not need to factory reset the device just to change networks
-
If the app method fails, a full reset followed by fresh setup is the fallback
Before You Start: What You Need
Getting these in order prevents the most common mid-process failure:
-
The Ring app, installed and signed in on your phone
-
Your new WiFi network name and password, the exact password including capitals and special characters. If you've forgotten it, check the sticker on your router or log into your router admin panel
-
Physical access to the doorbell, you need to press the setup button on the device itself, which means standing next to it
-
2.4 GHz WiFi available, most Ring doorbells only connect to 2.4 GHz. If your router broadcasts 2.4 GHz and 5 GHz under the same network name, you may need to temporarily separate them in your router settings, or stand closer to the router so your phone connects on 2.4 GHz during setup
-
Sufficient battery charge (battery models), a depleted battery will interrupt the process partway through. Charge to at least 50% before starting
The Standard Method: Change WiFi Through the Ring App

This works for Ring Video Doorbell, Ring Video Doorbell 2, 3, 3 Plus, 4, Pro, Pro 2, Wired, Elite, and Battery Doorbell Plus.
Step 1: Open Device Health
-
Open the Ring app
-
Tap the menu icon (≡) in the top-left corner
-
Tap Devices
-
Select your doorbell from the list
-
Tap Device Health
-
Under the Network section, tap the WiFi network name shown, then tap Change Network (some app versions show this as Change WiFi Network or Reconnect to WiFi)
You will see a warning that the device will go offline temporarily. Confirm to continue.
Step 2: Put the Doorbell in Setup Mode
The Ring app will prompt you to put the doorbell in setup mode. The setup button location varies by model:
|
Model |
Setup Button Location |
|
Ring Video Doorbell (1st Gen) |
Orange button on the back, remove from mounting bracket first |
|
Ring Video Doorbell 2 |
Remove faceplate; orange button below the camera |
|
Ring Video Doorbell 3, 3 Plus, 4 |
Remove faceplate; orange button below the camera |
|
Ring Battery Doorbell Plus |
Remove faceplate; orange button below the camera |
|
Ring Video Doorbell Pro |
Remove faceplate; button on the right side |
|
Ring Video Doorbell Pro 2 |
Remove faceplate; button on the right side |
|
Ring Video Doorbell Wired |
Remove faceplate; button on the right side |
|
Ring Video Doorbell Elite |
Button on the right side (no faceplate removal needed) |
Press the button until the light ring on the front starts spinning white, this indicates setup mode is active.
Step 3: Connect Your Phone to the Ring Network
Your phone will be prompted to join a temporary network called Ring-XXXXXX (where XXXXXX is a string unique to your device). This is a short-range WiFi broadcast the doorbell creates during setup.
On iOS, the phone usually joins this network automatically. On Android, you may need to go to your phone's WiFi settings, select the Ring-XXXXXX network manually, then return to the Ring app.
Step 4: Select Your Home Network and Enter the Password
Once your phone is connected to the Ring temporary network:
-
The app will display a list of available WiFi networks
-
Select your home network (2.4 GHz)
-
Enter the password, this is case-sensitive
-
Wait for the doorbell to connect, typically 30–90 seconds
-
The light ring will turn solid white briefly, then go off, this means the connection was successful
The Ring app will confirm the device is online. Check Device Health to verify the WiFi signal strength shows as Good or Very Good.
WiFi Band Compatibility: The Detail That Trips Most People
Most Ring doorbells only work on 2.4 GHz WiFi. This is the most common reason for failed setup after a router change.
2.4 GHz only (cannot connect to 5 GHz):
-
Ring Video Doorbell (2nd Generation)
-
Ring Video Doorbell Wired
-
Ring Battery Doorbell Plus
Compatible with both 2.4 GHz and 5 GHz:
-
Ring Video Doorbell Pro
-
Ring Video Doorbell Pro 2
-
Ring Video Doorbell Elite
If you recently switched to a new router that broadcasts a combined 2.4/5 GHz band under one network name, your doorbell may fail to connect even if you enter the correct password. The fix: log into your router admin panel and split the networks into separate SSIDs (e.g., "MyHome_2.4" and "MyHome_5G"), then set up the Ring using the 2.4 GHz SSID specifically.
Understanding how your home network affects device reliability is a theme that extends well beyond doorbells. If you're building out a broader smart home setup, how to automate home appliances covers how network preparation affects every connected device in your home.
When You Changed Your Router: Key Differences
If you got a new router (not just a new password), the process is identical, but a few things are worth double-checking.
If your new router has the same network name and password as the old one: The Ring doorbell may reconnect automatically without any action from you. Give it 5–10 minutes after the new router is live before concluding it needs manual reconfiguration.
If your new router has a different network name or password: Follow the full Change WiFi Network process above. The doorbell is still associated with the old network credentials and won't find the new one on its own.
If you're switching ISPs and got a completely new router: Same process. One additional step: your Ring Base Station (if you have Ring Alarm) also needs to be reconnected separately, it has its own network settings in the Ring app.
What to Do If the App Method Fails
App Shows "Change WiFi Network" But Nothing Happens
Close the Ring app fully, reopen it, and try again. If the doorbell isn't in setup mode when the app looks for it, the process silently fails.
Doorbell Won't Enter Setup Mode
If pressing the setup button does nothing, or the light ring behaves unexpectedly:
-
Confirm the battery has sufficient charge (battery models)
-
Hold the setup button for 5 full seconds rather than a brief press, the light should flash before spinning
-
If the doorbell has been offline for an extended period, it may take up to 2 minutes to fully wake before responding to setup mode
Stuck on "Connecting to Ring Network"
If your phone connects to Ring-XXXXXX but the app doesn't advance:
-
On Android: after joining Ring-XXXXXX in WiFi settings, manually switch back to the Ring app, it doesn't always auto-resume
-
Disable mobile data temporarily on your phone, some Android devices route app traffic through cellular data even when connected to a WiFi network, which prevents the setup from completing
-
Toggle your phone's WiFi off and back on, rejoin Ring-XXXXXX, then return to the app
Setup Completes But Doorbell Shows Offline in the App
This usually means the WiFi password was entered incorrectly. The doorbell accepted the attempt but couldn't authenticate with the router.
-
Repeat the Change WiFi Network process
-
When entering the password, tap the eye icon (if available) to show the characters and verify each one
-
Confirm you're selecting the 2.4 GHz network if your router broadcasts both bands separately
The Fallback: Factory Reset and Fresh Setup
If the Change WiFi Network method consistently fails, the process completes but the device never comes online, a factory reset wipes the stored WiFi credentials and lets you set up the doorbell from scratch.
This should be a last resort. It removes the device from your Ring account and requires re-adding it, which means reconfiguring all your notification settings and zones.
How to Factory Reset a Ring Doorbell
-
Open the Ring app → Devices → your doorbell → Device Settings → General Settings → Remove This Device
-
At the doorbell, press and hold the setup button for 20 seconds, then release
-
The LED will flash for about a minute, this confirms the reset is complete
-
Open the Ring app → Set Up a Device → Doorbells and follow the fresh setup process
Checking WiFi Signal Strength After the Change
Once the doorbell is back online, check the signal quality:
Ring app → Devices → your doorbell → Device Health → scroll to Network.
The RSSI (Received Signal Strength Indicator) number shown tells you signal quality:
|
RSSI Value |
Signal Quality |
|
−40 to −60 |
Excellent |
|
−61 to −70 |
Good |
|
−71 to −80 |
Fair, may cause delays |
|
Below −80 |
Poor, reconnection issues likely |
If signal quality is Fair or Poor after changing networks, the router may be too far from the doorbell. A WiFi extender or mesh node placed between the router and the front door is the most reliable fix. Ring also sells its own Ring Chime Pro, which includes a WiFi extender function built in.
Weak signal is the leading cause of recurring offline issues, dropped live views, and delayed motion notifications. If you're experiencing these after a router change, signal strength is the first thing to check before assuming the change process itself failed.
If you want to understand how your camera's alerting behavior connects to signal quality and AI detection, how do motion alerts work on security cameras explains how network reliability affects what alerts actually reach you and when.
Ring Subscription: Does It Affect WiFi Change?
No. Changing WiFi networks on a Ring doorbell does not require a Ring Protect subscription. The Change WiFi Network function is part of the device's core setup and works regardless of your subscription status.
What Ring Protect affects is video history and some AI detection features, not the connection process. This distinction matters if you're evaluating the ongoing cost of running Ring. For a broader comparison of how subscription costs add up across smart home security devices, how on-device AI saves you $200+ a year breaks down where those costs come from and what a subscription-free architecture looks like.
Ring Doorbell WiFi and Privacy: What You Should Know
Every time your Ring doorbell operates, it sends footage and metadata to Amazon's cloud servers for processing. This is how Ring's motion detection, AI alerts, and video history work, the camera captures, the cloud processes, you receive a notification.
When you change your WiFi network, you're changing the path this data takes from your home to Ring's servers, but you're not changing the fact that it travels there. Your footage and detection events are processed externally by default.
This matters most to homeowners who've started thinking carefully about where their home security data goes. If this is a concern for your household, understanding the difference between cloud-processed and on-device AI security is worth time before your next security purchase. OVAL AI Home Hub: the future of privacy-first security covers what on-device processing actually means for the data your cameras generate.
Using Ring in an Apartment or Rental Property
Renters frequently search this topic after moving to a new apartment and needing to reconnect their doorbell to a new network. A few considerations specific to rental settings:
Most apartment buildings use 2.4 GHz WiFi, confirm with your building manager before purchasing or setting up any Ring device if you rely on building-provided WiFi.
If you're using a Ring doorbell on an apartment door (interior hallway), bear in mind that Ring's cameras and motion detection capture whatever is in their field of view, including hallways, common areas, and potentially neighboring units. Check your lease and building rules before installation.
Battery-powered Ring doorbells (Video Doorbell 4, Battery Doorbell Plus) don't require hardwiring and can be removed when you move, making them more renter-appropriate than wired models. If you're evaluating options for renter-friendly security more broadly, smart home on a budget: where to start if you can only buy one device includes security options that work without permanent installation.
Considering an Upgrade Beyond Ring?
If you've been through this process a few times and found yourself questioning whether Ring's cloud-dependent setup is what you want long-term, the recurring subscription, the footage traveling to Amazon's servers, the limited AI intelligence, there's a different category of front-door security worth knowing about.
OVAL by IRVINEi, hellooval.com is an AI Home Hub with on-device Edge AI that processes everything locally, no footage leaves your home network, no subscription required for core features, and 11 contextual alert categories (visitor, package, intruder, weapon detection, fall, toddler wander, and more) built in. IP65 weatherproof, Gorilla Glass, and 3,000+ device integrations in a single device at your front door. If Ring's limitations have become visible, OVAL is the next step worth exploring.
Conclusion
Changing the WiFi on a Ring Video Doorbell takes about five minutes and follows the same path on every model: Ring app → Device Health → Change WiFi Network → setup mode → select new network → enter password. The process doesn't require a factory reset, doesn't affect your subscription, and doesn't delete your settings.
The most common failure points, wrong WiFi band, incorrect password entry, phone data interfering with the setup connection, are all avoidable with the preparation steps outlined above. If the standard app method fails completely, the factory reset path is reliable but means reconfiguring your device from scratch.
Once you're back online, check your RSSI signal strength in Device Health. A weak signal after a router change causes more recurring problems than the WiFi change process itself.
For anyone thinking about whether Ring's setup is working for your home beyond just the WiFi connection, 10 signs your home security system is outdated is a useful benchmark for what current security systems should actually be capable of.
Frequently Asked Questions
How do I change the WiFi on my Ring Video Doorbell?
Open the Ring app, tap the menu (≡), go to Devices, select your doorbell, tap Device Health, then tap Change WiFi Network or Reconnect to WiFi. Stand next to the doorbell, press its setup button until the light spins white, follow the in-app prompts to connect to your new network, and enter the password when prompted.
Do I need to factory reset my Ring doorbell to change WiFi?
No. The Change WiFi Network option in Device Health handles this without a reset. A factory reset is only needed if the app method repeatedly fails, it wipes all settings and requires starting setup from scratch.
Why won't my Ring doorbell connect to my new router?
The most likely causes are: you're trying to connect to a 5 GHz network (most Ring doorbells only support 2.4 GHz), the WiFi password was entered incorrectly, or your phone switched to cellular data during setup, blocking the process. Check these three things before assuming a hardware problem.
Can I change the WiFi on my Ring doorbell without the app?
No. WiFi credentials are stored on the doorbell and can only be changed through the Ring app's Device Health screen. There is no web interface or hardware-only method for changing the network.
What does the RSSI number mean in Ring Device Health?
RSSI (Received Signal Strength Indicator) measures the WiFi signal your Ring doorbell is receiving. Values between −40 and −60 are excellent. Between −61 and −70 is good. Below −70 is fair to poor and may cause delayed alerts, dropped live views, and reconnection issues. A WiFi extender between your router and the doorbell improves a weak RSSI.
Does changing WiFi on Ring cancel my Ring Protect subscription?
No. Your Ring Protect subscription is tied to your Ring account, not your home network. Changing the WiFi network has no effect on subscription status, video history, or any account features.
What if my Ring app shows "Change WiFi Network" is grayed out?
This sometimes happens when the doorbell has been offline for too long. Try pressing the setup button on the device first to wake it, wait two minutes, then reopen the app and try again. If the option remains grayed out, a factory reset followed by fresh setup is the resolution.